AUTONET TV

Have a Ball! Know your Ball Joints (Ball Joints)

We all have joints in our own skeletal system, but did you know your vehicle has some joints of its own? One of the most important is called a ball joint.

One of the interesting things is that it's somewhat similar to the ball and socket joints we have in our hips and shoulders.  A ball joint allows two parts it joins together to move in more than one direction at the same time.

Think about your wheels.  They have to move up and down when there are bumps in the road but in sideways directions when you are making a turn. As you can see, the ball joints are important for your steering and handling to work correctly.

Since ball joints do so much, they can wear out and become loose.  When the ball wears down or the socket gets worn, there can be too much play in them.  It can get so bad that the ball can come out of the socket and your wheel can fall off, a dangerous situation.  Ball joints can also seize up.  Some of them are sealed and never require maintenance; others require periodic lubrication.

Here are some signs that your ball joints are going bad:

• Your vehicle pulls to one side
• You can hear a clunking noise coming from a wheel area
• Your tires are wearing unevenly, especially on the inside

The earlier a failing ball joint is discovered, the better. The best way is to have regular inspections by a technician.  Your service facility will periodically check ball joints at intervals recommended by the manufacturer. The cost to replace them can vary widely depending on whether you have a vehicle with a 2-ball or 4-ball configuration.  Also, sometimes just the joints can be replaced, but other times they are part of a larger control arm assembly that has to have all the parts replaced at the same time. 

Your vehicle's proper steering, handling and tire wear all contribute to a better, safer driving experience.  Make sure your ball joints are up to the job.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

No Fountain of Youth (Aging Tires)

Can you think of anyone who enjoys aging?  Wrinkles where you don't want them, gray hair, eyes that won't focus any more, no stamina. 

Believe it or not, your tires age, too, and they don't get better the older they get.  And here's the important thing to know, even if they can still pass a tread depth test, they may simply be too old to be safe 

Here's the best way to understand this.  Have you ever found an old deck of playing cards with a rubber band wrapped around them?  Try stretching the rubber band.  SNAP! It's all cracked and brittle.  And you haven't stressed that rubber one bit since the time you put them in that drawer.

Now you know what's happening to your tires.  Rubber ages.  Just like us, the day we come into the world, we start to go downhill (no pun intended).  Oh, engineers are able to make a tire last longer than ever before.  But that gas that keeps us alive—oxygen—seems to love to chemically mix with some components in rubber.  Oxidation causes rubber to become hard and brittle.  The rubber band test.

Is there an age test that can tell you when a tire is tool old to roll? Well, not really.  They don't all age the same.  Hot climates can make tires wear out more quickly.  Some experts say a tire can last up to 10 years but should be inspected every year after the age of five.  Others say tires should have an expiration date at six years old.

Since no one would ever ask a tire its age, how do you know how old one is? Believe it or not, tires made after the year 2000 have a date code stamped on either the inside or the outside of the sidewall.  It's a four-digit numbers; the first two tell you the week, the second two tell you the year. So if it has the number 1916, it was made in the 21^st week of 2016. 

Another way to find out if your tires still have enough life in them is to have your vehicle service facility inspect them.  They look for signs of age, such as developing cracks in the rubber, the condition of the sidewalls and, of course, that old standby: tread.  If it's time to "retire" them, discuss options with your service advisor.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

A Sticky Brake Situation (Parking Brake Service and Maintenance)

We've all been there.  You park your vehicle on a steeper than usual hill and worry about it rolling down while you're running your errands.  So you decide you'll use the parking brake.  When you get back, you release the parking brake, hit the ignition, put it in gear and—uh, oh—you can feel the parking brake is still on.  It's stuck.  What do you do now?

Welcome to the world of infrequently-used parking brakes.  Yes, they do stick for several reasons. It's common for components to corrode and get locked up.  Sometimes if you have applied it extra hard, it can jam.  Could be a rusty cable, could be a spring that doesn't return the brake to its disengaged position.  Some pieces just break when they're stressed for the first time in a while. A caliper or the pivot arm it's on can also stick.

There are a few things you can try to unstick it.  Carefully rock your vehicle by putting it first in drive and then reverse.  You have to be careful doing that, though, because sometimes you can damage the transmission.  You can try working the parking brake control a few times to see if that will loosen the corrosion.  If you can't unstick it, you can try driving slowly a short distance to a repair facility near you.  Sometimes it won't cause damage to the brakes but it depends on how tightly the parking brake was applied and what was stuck.  You may also have to have your vehicle towed to a repair facility.

In any case, once you've seen these symptoms, have your vehicle brakes looked at by a professional who can fix the root of the problem.  Better yet, don't let your vehicle get in this condition; regular maintenance and inspections by a trained technician should prevent you from getting in a jam somewhere thanks to a stuck parking brake.  You could use a "brake" like that.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

Getting from E to F (Fuel Gauge Problems)

Who thinks about their fuel gauge?  You probably don't… until it doesn't work any more.  Then you have to guess how much fuel is in your tank, and that's no way to live life on the road. 

Fuel gauges, like every other part in your vehicle, can fail.  And when yours stops working, you will probably want to head over to your service facility soon, because no one relishes running out of fuel.

The fuel gauge system is much more than just the gauge you can see on your instrument panel. Most systems have a float inside the fuel tank that goes up and down depending on the fuel level.  It's called the fuel sending unit, and it sends an electrical signal to the gauge (on the dash) telling it to display how much fuel is left in the tank. 

So, what could go wrong?  Well, a few things.  For one thing, corrosion from bad fuel can cause it to stick and it won't move up and down any more.  So you could fill up your tank and the gauge would still read Empty.  If a sending unit needs to be replaced, often the parts can be costly. The good news is that fuel sending units rarely fail and most drivers will never have one go bad.

Other things that can go wrong? An electrical problem could cause a fuse to blow and you won't get a reading at all.  A technician can figure out where that electrical problem is and how to repair it.  Finally, it's possible for the gauge itself (on the instrument panel) to fail.

One thing to keep in mind is if your fuel gauge isn't working, you might be tempted to carry around an extra container of fuel.  That's ok if it's outside the cabin, such as in the bed of a pickup.  But if you carry it inside the cabin or trunk, fuel fumes can be very dangerous for your health, even fatal.

A working fuel gauge gives you peace of mind… so you'll never have that "empty" feeling.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

See the Light (Automatic High Beam Dimmers)

It's happened to all of us.  We're driving down a highway at night and over a crest appears a car with its high beams blazing.  You are momentarily blinded, hoping the other driver will switch them to their low beam setting and restore your vision.

Not only do we not appreciate being blinded, face it; we don’t want to be that other driver, either.  You know, the one who forgets to turn down their high beams.

Why do we want high beams in the first place? They can improve safety when used correctly, giving drivers more reaction time since they can see farther down the road.  But research has found many drivers either don't use them or, when they do, they frequently forget to switch to low beams.  Enter the automatic high-beam dimmer.

The quest for the perfect one began back in the 1950s, General Motors invented something it called the "Autronic Eye." It was a phototube which sat on the dashboard and turned down your beams when it saw other headlights.  While touted as being the biggest advance in night driving safety in 30 years, it didn't work all that well.  But as technology got more advanced, systems improved.

Today's automatic high beam dimmers usually have a camera in the rear view mirror (pointing forward).  When the camera sees lights, software in the system's computer attempts to determine the source of the light, whether it is an oncoming vehicle, taillights, ambient city lights, street lights or the reflection off of a street sign.  It then adjusts the headlights to operate high beams if appropriate or a less-blinding mode if they’re not.

Some automakers are striving to make their headlight systems smarter and safer by developing lamps that can avoid blinding oncoming drivers by means other than simply dimming them. One idea? Splitting the beams so they will block just the portion that shines into the eyes of oncoming drivers.

It's a long way from the Autronic Eye. 

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

Move it or Lose It (Dormant Vehicles)

When it comes to your vehicle, driving it too much can cause some issues.  But what about not driving a vehicle enough? That has consequences as well.

Here are a few things that can happen if a vehicle isn't driven enough.  When the engine doesn't operate, the oil isn't lubricating. That means some mechanisms that need periodic lubrication aren't getting it.  And oil that sits around breaks down over time.  In fact, some experts say you should change oil more often if your vehicle sits in the driveway than if you drive it regularly. 

You've heard that expression, "Take it on the highway and blow out the engine.” Well, carbon buildup used to be a problem in older vehicles.  But the real culprit these days is moisture that builds up from combustion if your vehicle never gets hot enough to burn it off. That water vapor can mix with oil and cause sludge to form. There are many vehicle systems (battery, exhaust system, engine seals, etc.) that benefit from driving your vehicle at its optimal operating temperature for a while.

Spark plugs can deteriorate unless they are fired up.  The gas tank can rust from the inside if the metal is exposed from not having fuel in it.  Rodents and insects may see a sitting vehicle as a luxury hotel.  Brakes can rust after sitting around without being used.  Seals and gaskets can dry out.

One wise thing to do is check the operating manual. Some will spell out a maintenance schedule for vehicles that aren't driven regularly. 

One suggestion? Discuss your vehicle's maintenance with your service advisor. Let him or her know how often you drive the vehicle and what you use it for.  Then, you can come up with a maintenance schedule tailored for you, one that might not be covered in the owner's manual. 

If you do have a vehicle that's been sitting around for a long time, it may be wise to have it towed to your service facility rather than trying to drive it with brakes that may not work, spark plugs that may not fire reliably and other systems that may compromise your safety and those of others on the road. 

You may think it's great to have a low-mileage vehicle that you've barely driven, but a complicated, sophisticated machine such as a car, SUV or truck needs regular attention to keep it running safely… and reliably.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

How Tired Are Your Tires? (Tire replacement)

Of the things you think about most, your tires are probably pretty far down the list. That’s understandable because today’s tires are engineered to do their job without needing you to pay too much attention to them. But they DO wear out, and worn tires can contribute to skidding in bad weather, not being able to stop, a ride full of uncomfortable vibrations and, even a sudden blowout. Yikes. Let’s figure out right now how to know if your tires need replacing!

Let’s face it. Most of us don’t know the first thing about tires. So, the best way to make sure what shape yours are in is to take your vehicle to a qualified service facility to have the tires checked out by a trained technician.  Here are things they’ll check:

• Tread.  Tread is the part of the tire that touches the road surface.  Different tires have different tread patterns and something called tread blocks - the raised rubber parts that contact the road. The longer a tire has been on a vehicle, the more of that rubber wears off.  The technician will check to see if there’s enough of that tread left on your tire for sufficient traction to accelerate, steer, and brake.
• Pressure. It’s important your tires be inflated properly so your tires will perform the way they’re designed while driving.  If your tires have low air pressure, the technician will check to see why, perhaps cracks in the sidewall from age, a nail in the rubber picked up on the road, or bulges. It’s also important your tires are not overinflated too.
• Wear.  Your tires should wear evenly.  If they haven’t, the uneven wear can cause vibrations that you can feel in the steering wheel.  Maybe the whole vehicle shakes at a certain speed.  Your vehicle may require other services such as balancing, alignment, or suspension repairs to prevent future tire damage.
• Age.  Your tires may have adequate tread, but if they’re too old, it’s time for new. Rubber gets old, and when it does, it loses its elasticity.  Ever find an old rubber band and tried to stretch it? It’s brittle and will break easily. Hotter climates will age rubber—and tires—faster. All tires have their date of manufacture stamped on them, so your service adviser will be able to see when your tires were made.

If it’s time to replace your tires, you’ll find you have many choices for new ones: different brands, models, designs, etc.  Your service adviser can help you figure out which ones are right for you. It’s much better—and safer—to do it before one of them fails at the least opportune time.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

Tire or Re-Tire? (Getting Tires Ready for Hot Weather)

Heat isn't easy on vehicle tires, and as the seasons change, make sure yours are ready to take the heat. 

Let's talk first about inflation.  Heat causes air to expand, so heat alone can raise the pressure in your tires.  If you are driving on overinflated tires, they won't have as much contact with the road surface.  In that case, it will take you a longer distance to stop.

On the other hand, you don't want your tires to be underinflated during hot weather, either.  That can cause your sidewalls to flex.  Friction will then hike up the temperature and your tire can be in danger of blowing from the added heat.

Other things can cause problems, such as uneven wearing.  Your service advisor knows the signs to look for and can diagnose where the wear is and what is likely causing it.  Another thing a technician will look for on tires is tread depth and the condition of the sidewalls.  Any cuts, cracks or bulges could be indications that your tire is not healthy. 

Oh, and one other thing.  Your tires could have plenty of tread left on them but still be dangerous.  And that is because rubber ages, gets brittle and cracks after time.  (Ever run across an old rubber band in a drawer that has never been used but breaks the second you try to stretch it? 'Nuff said.) Some tire manufacturers recommend replacing tires after 6 years of their manufacturing date.  Your service advisor can read a manufacturing code and tell you how old your tires are. 

Tire manufacturer Michelin used to have an ad slogan that said, "Because so much is riding on your tires." That includes you and your passengers.  Always keep healthy tires on your vehicle and make sure they're ready for whatever season it is.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

The Red Menace (How to Deal with Rust)

Rust.  It's worse if you drive in places that use salt on the roads in winter, or if you spend time driving near a body of salt water.  But any vehicle has to deal with rust after years on the road.  And it's not just that rust can eat away your vehicle's body and fenders.  It can be a real problem around your suspension, drivetrain or any place where there's metal.

Rust takes its time.  You don't see it until it's already done its dirty work.  It can wreak havoc with your electrical system.  Sure, vehicle manufacturers do their best to keep it to a minimum, but especially with road treatments like brine around, their task is a difficult one.

The one spot everyone notices is in the paint.  You see a little bubbling under the once-smooth surface.  By the time it bubbles, it's well involved in rotting away that spot of your vehicle.  You wouldn't believe how just a little thing can start the process on its way.  A stone chips the paint down to the metal, moisture and salt reach the steel and rust is off and running.  It could be a scratch in the paint, a little dent, acid from a parking garage, tree sap, you name it.  If you spot it, show it to your service advisor because rust can be more than a cosmetic problem.  It can be a safety issue.

While you can see the rust destroy your vehicle's body, you can't see it destroying your engine.  But it can.  It can eat away at such areas as air intakes or the exhaust system.  Not only can it reduce performance, but also it can disable electrical connections.  In this day and age where just about everything in your vehicle has a computer component to it, just a small electrical problem can strand you at the roadside.

Corrosion can attack your vehicle's chassis or frame, and they are what provide the structural strength and stability for everything attached.  Think powertrain, suspension, axles, window frames. The list goes on and on.  Structural integrity is vital to safety, so the stakes are high. 

Now you can see why rust damages more than just the good looks of your vehicle. There's one thing to remember about corrosion - much of it is only visible from underneath the vehicle.  When you bring your vehicle in to AutoSurgeonInc for service, our technician can look for any problems from that important vantage point.  It's always a good idea to point out any spots that you think might spell trouble.  That way you can stay ahead of it and beat rust at its own game.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940

Power Failure (Broken Power Seat)

Know anyone who doesn't love a power seat in an SUV, a car, truck or van? They're convenient and precise in their adjustments.  But when they break, oh, what a pain.  Not only is it inconvenient, it may leave your seat position too close to the steering wheel or too far from the pedals.  This is a must-fix problem.

There are many things that cause a power seat to fail:

• Seat controls.  These are either at the side of the seat or in the door.  Both are places that can be exposed to moisture or other contaminants.  When the controls stop working, they usually need to be replaced.
• Seat motor.  Electric motors are what make a power seat move, and sometimes they fail.  Sometimes they just get worked to death and die of old age.  Replacement is the most common remedy.
• Fuses. A power seat is, after all, powered by electricity and all vehicle power systems have fuses to protect them.  A technician can determine which fuse may have blown and replace it.  But it's also important to figure out what caused the fuse to blow and deal with that, too.
• Wires.  There are wires under the seats that move when you move the seat.  Sometimes they get stretched, kinked or ripped.  In a power seat malfunction, it may be a wiring harness that needs to be replaced.
• Gears.  They help the seat move and may need to be realigned or replaced.
• Obstructions.  Yes, a piece of trash or a kid's toy has been known to jam up the works of a power seat. Taking them out of the mechanism may get your seat working again.

Most people pay extra to have power seats in a vehicle. So make sure you keep that convenient feature working. And don't forget that it's a safety issue, too.

AutoSurgeonInc
1820 E Kalamazoo St
Lansing, Michigan 48912
517-374-8940